[j-nsp] routing instances on EX2300

[Valentini, Lucio]

Hi there,

I was trying to configure routing instances on the EX2300, like I did on the EX4300, but it seems it´s not possible.

I compare the EX4300 and the EX2300; as far as the licenses are concerned, the output of the command "show system license" is almost the same. I say almost, because in the column "Licenses used" I see ospf2 and virtual router for the Ex4300, as shown below,

show system license
License usage:
Licenses Licenses Licenses Expiry
Feature name used installed needed
ospf3 0 1 0 permanent
ripng 0 1 0 permanent
ospf2 1 1 0 permanent
bfd-liveness-detection 0 1 0 permanent
unicast-rpf 0 1 0 permanent
virtual-router 1 1 0 permanent
igmp 0 1 0 permanent
pim-mode 0 1 0 permanent
pim-ssm 0 1 0 permanent
connectivity-fault-management 0 1 0 permanent
vrrp 0 1 0 permanent
dot1q-tunneling 0 1 0 permanent
svlan 0 1 0 permanent
services-rpm 0 1 0 permanent
juniper-msdp 0 1 0 permanent
multicast-listener-discovery 0 1 0 permanent
gr-ifd 0 1 0 permanent

Licenses installed:
License identifier: JUNOS835695
License version: 4
Valid for device: TW3716360248
Features:
extended-feature-list - Licensed extended feature list
permanent


but I don´t get that on the EX2300, where I get all zeros, even though the configuration is the same (2 routing instances with ospf, other than the main).

However, when I go into configuration mode on the EX4300, I get this

# set routing-?

routing-instances Routing instance configuration
routing-options Protocol-independent routing option configuration

{master:0}[edit]

The configuration includes:

set routing-instances Didattica instance-type virtual-router
set routing-instances Didattica interface irb.204
set routing-instances Didattica interface irb.101
set routing-instances Didattica routing-options router-id 10.245.2.190
set routing-instances Didattica protocols ospf spf-options delay 800
set routing-instances Didattica protocols ospf spf-options holddown 4000
set routing-instances Didattica protocols ospf export Export-Statics
set routing-instances Didattica protocols ospf area 0.0.0.0 interface irb.204 interface-type p2p

and it works OK.
But when I do the same on the EX2300, I get this:
w# set routing-?

routing-options Protocol-independent routing option configuration

{master:0}[edit]

As you can see, only 1 completion is possible. It accepts the same snippet above, without giving any error, but it does not work.

Can you confirm that ? or else, how can I get 2 routing instances to work on the EX2300, together with the main instance ?

Thanks

Cheers

Lucio



_______________________________________________
juniper-nsp mailing list juniper-***@puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-nsp

[Olivier Benghozi]

According to the Feature Explorer, VRF Lite are supported on EX2200, but not on EX2300. Reducing the feature set of new products is just ridiculous...

Post by Valentini, Lucio
I was trying to configure routing instances on the EX2300, like I did on the EX4300, but it seems it´s not possible.

_______________________________________________
juniper-nsp mailing list juniper-***@puck.nether.net
https://puck.nether.net/mailman/listinfo/juniper-ns

[Valentini, Lucio]

I agree with you 110%, I hope it´ll be on the roadmap like the "oam", because it is really a disappointing thing, particularly if I think the EX2300 was introduced as an improvement on the "old" EX2200!

But where you get the Feature Explorer? Is this link the right one?

https://pathfinder.juniper.net/feature-explorer/select-platform.html

Cheers

Lucio

-----Messaggio originale-----
Da: juniper-nsp [mailto:juniper-nsp-***@puck.nether.net] Per conto di Olivier Benghozi
Inviato: giovedì 23 marzo 2017 11:23
A: juniper-***@puck.nether.net
Oggetto: Re: [j-nsp] routing instances on EX2300

According to the Feature Explorer, VRF Lite are supported on EX2200, but not on EX2300. Reducing the feature set of new products is just ridiculous...

Post by Valentini, Lucio
I was trying to configure routing instances on the EX2300, like I did on the EX4300, but it seems it´s not possible.

_______________________________________________
juniper-nsp mailing list juniper-***@puck.nether.net https://puck.nether.net/mailman/listinfo/juniper-nsp
_______________________________________________
juniper-nsp mailing list juniper-***@puck.nether.net
https://puck.

[Olivier Benghozi]

Yes, for EX2300 it's https://pathfinder.juniper.net/feature-explorer/select-platform.html?category=Switching&typ=1#family=&pid=30502300&platform=EX2300&rel=15.1X53-D55&sid=799&stat=0.4850388479542256&swName=Junos+OS <https://pathfinder.juniper.net/feature-explorer/select-platform.html?category=Switching&typ=1#family=&pid=30502300&platform=EX2300&rel=15.1X53-D55&sid=799&stat=0.4850388479542256&swName=Junos+OS>

Post by Valentini, Lucio
I agree with you 110%, I hope it´ll be on the roadmap like the "oam", because it is really a disappointing thing, particularly if I think the EX2300 was introduced as an improvement on the "old" EX2200!
But where you get the Feature Explorer? Is this link the right one?
https://pathfinder.juniper.net/feature-explorer/select-platform.html
-----Messaggio originale-----
Inviato: giovedì 23 marzo 2017 11:23
Oggetto: Re: [j-nsp] routing instances on EX2300
According to the Feature Explorer, VRF Lite are supported on EX2200, but not on EX2300. Reducing the feature set of new products is just ridiculous...

Post by Valentini, Lucio
I was trying to configure routing instances on the EX2300, like I did on the EX4300, but it seems it´s not possible.

_______________________________________________
juniper-nsp mailing list juniper-***@puck.nether.net
https://puck.nether.n